Wheel build/rebuild Sturmey Archer Hub, Schindelhauer Bike, Gates Belt Drive

Our Community › Forums › Bikes & Equipment › Wheel build/rebuild Sturmey Archer Hub, Schindelhauer Bike, Gates Belt Drive

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • July 2, 2015 at 1:39 am #1033325
    Phatboing
    Participant

    Ooh ooh ooh.

    I’ve been dilly-dallying on selling my Soma Iggy wheelset, with a 5-speed Sturmey Archer. Fits former fixie frames (120mm spacing)

    But! Chain drive.

    July 2, 2015 at 2:10 pm #1033338
    83b
    Participant

    The Daily Rider sees lots of belt drive bikes and did a great job building me a wheelset that included a weird-sized electric motor hub. And they were highly accommodating of highly-specific thoughts regarding the build (read: my many neuroses!). It’s a bit of a haul from Fairfax, but would give you an excuse to visit one of the cool restaurants/bars on H St (my favorite, hands down, is the Queen Vic).

    July 2, 2015 at 2:39 pm #1033343
    hozn
    Participant

    I would recommend just building a new wheel rather than rebuilding the existing wheel with the new hub. At best you could reuse the rim, but it doesn’t look like the bike comes with great rims (Alexrims), so I’d just spend $50-$80 to get a good rim (e.g. Kinlin has some nice options in both wide and “old-school” [narrow] that are quite affordable) and then you have a spare rear wheel.

    July 2, 2015 at 3:25 pm #1033348
    ShawnoftheDread
    Participant

    I work with a guy who has a single speed Schindlhauer with a belt drive. He says he has to order their hub for replacement because of the special dropouts, with the only US distributor being a single guy in Wyoming, and that the belt drive tension wears out the hub so quickly they only last him about eight or nine months. Sounds both crazy and suspicious to me.

    July 2, 2015 at 4:52 pm #1033352
    hozn
    Participant

    Why not just get the Ludwig built with/for the Alfine hub?

    http://www.schindelhauerbikes.com/en/bikes/Ludwig.html

    July 2, 2015 at 5:28 pm #1033356
    americancyclo
    Participant

    @ShawnoftheDread 119417 wrote:

    with the only US distributor being a single guy in Wyoming.

    This place? Jackson mailing address, but LA area code.

    Belt DR USA

    199 E Pearl Ave, 101
    Jackson, WY, USA
    83001
    Phone :: 310 402 2367
    Email :: sales(at)beltdr.com

    July 2, 2015 at 5:49 pm #1033357
    ShawnoftheDread
    Participant

    @americancyclo 119427 wrote:

    This place? Jackson mailing address, but LA area code.

    Probably, though I’ve said all I know about the situation. It’s a nice looking bike though.

    July 2, 2015 at 8:12 pm #1033365
    Steve O
    Participant

    @dplasters 119390 wrote:

    I’m getting this bike. But with these drop bars.

    I note that the front and rear wheels are laced differently. It strikes my eyeball as odd, but there must be a good reason.

    July 3, 2015 at 12:02 am #1033371
    vvill
    Participant

    @Steve O 119436 wrote:

    I note that the front and rear wheels are laced differently. It strikes my eyeball as odd, but there must be a good reason.

    Why is that odd? I thought it was quite common, since the rear has to deal with the torque of the drivetrain.

    These bikes do look really nice. I would be tempted if, yeah. I like that they give you a flip flop hub too – not common with belt drives afaik.

    July 3, 2015 at 12:07 am #1033372
    hozn
    Participant

    Yeah, radial lacing is pretty much the standard for rim-brake road front wheels. What looks a little odd is a front radial wheel with so many spokes. But the large hub flanges should accommodate the high spoke count radial lacing without risk of flange breaking.

    July 3, 2015 at 2:09 am #1033374
    dplasters
    Participant

    @hozn 119422 wrote:

    Why not just get the Ludwig built with/for the Alfine hub?

    http://www.schindelhauerbikes.com/en/bikes/Ludwig.html

    Not willing to go di2 just to get hoods. Much prefer drops with hoods.

    I’ve thought about getting a kinlin rim. I haven’t see what kind of weight difference there really is.

    I’d not heard anything about the hubs wearing out. That sounds really odd and I’m not sure how that would happen. Given that I rode my S2 through the whole winter and several reviews say it is worthless in the winter I take it all in stride. I’m a low fuss rider.

    It is definitely a one or two person shop in Wyoming. Beltdr.com is the site.

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.